12/18/19 Here is a list of mods made to my 4.2L Swap Into My 2000 V6 Mustang;
She Needs The Tune.
2000 4.2 Short Block New
Shaved Mains With Morana Stud Girdle
ARP Main Studs
COMP Cams 44-702-9 Xtreme Energy Hyd. Roller Camshaft
ARP Head Studs
New Compcams Beehive Valve Springs
Keepers From Compcams
Melling Timing Chain Kit
Melling Oil Pump
Manley .120 Wall Push Rods
302 V8 Roller Lifters Compcams
Scorpion 1.73 Roller Rockets
Ported Upper And Lower Intakes
ACCUFAB RACING F70V6-1 70MM Throttle Body
19Lbs 7 Pintel Injectors
Oil Cooler , Inner And Outer Cooling Fans
3 Row Radiator
And A Lot More Blood And Sweat!!
Off The Top Of My Head That's The Internals
Almost On Road!! Close!!
10/18/19 NOW: Been A Couple Of Years Rebuilding My 2000 Mustang Changed: Now 4.2L V6, 50/50 Comp Cam, Scorpion Roller Rockers, Comp Cams 302 lifters Manley .120 Wall Push Rods, Shaved Main Caps For Morana Stud Girdle, F150 4Wheel Drive Oilpan To Fit Over Main Caps, (3.8L Not Workable) Will List As I Get Time Everything Else. Or See Pictures Below!
Then: Improving Handling and Run Ability In General,3.8L 5 Speed
I've Upgraded The Ignition, Accel Coil Pack, Bosch +4 Plat- Iridium Plugs, Wires, Cold Air Induction, Converted To Duel Exhaust, Shorty Headers, New Injectors (Bosch 4 Pintel 19# Upgrade). 9.8124R Sway Bar End Link Kit Red Performance Polyurethane, Have KYB Shocks All Around, Front Coil Overs, Engine Strut Brace, Full Tubular K Member UPR Front Suspension , Upper and Lower Rear Control Arms With Torque Boxes And Rear Sway Bar Installed, New Lowered Springs Rear, 1.5 Spacers Front 2" Spacers Rear,17"X9 AM Classic 5 Spoke Wheels with General G-MAX AS-03 Tire 245/45ZR17SL 95W BW All around. But You Could Say I've Not Made Any Other Mods. Truth Is I Do Plan Others! That's Why I'm Here To Pick Brains And Get Other Ideas. Powers No Good If You Can't Put It On The Ground!!!. 2000 Mustang Coupe Base
New 9/1/16: 19lbs 4 pintel injectors from 5.0 , Ported Upper And Lower Intakes, 70MM Throttle Body , New K Member ,Coil Overs, Scorpion 1.73 Roller Rockers, Manley Push Rods .020 Over Stock, Al Driveshaft, Modified Exhaust With Balance Tube, Duels, 373's LSD , 2800 Lb. Clutch, P&P, Heads Out Of Machine Shop (Ported) I'm Getting There!
6/12/17 Have 12 Pintel 24# Injectors To Install With Phenolic Spacer Between Upper And Lower Manifold, Moog Front Hubs. I'm LQQKING Into Upgraded Fuel System.
6/28/17 Still Working On Front End, Installed Offset Bushings To Steering Rack On UPR K Member, New Inner Tie Rods, Boots And Bump Steer Kit New Brake Dust Shields And Hub Spacers.
Getting Old Taking More Time Than It Used Too!!!
7/7/17 Installed 30MM Front Sway Bar With Prothane Bushings, Replacing 25MM Sway Bar. Now 30MM Front And 23MM Rear.
Welcome To V6Mustang.com!
We are the oldest and largest V6 Mustang forum on the internet. If you have any questions about your V6 Mustang or just want to connect with other V6 Mustang owners around the world, you have found the best place on the internet to do that.
Registering is free and easy! Hope to see you on the forums soon!