Welcome To V6Mustang.com!

We are the oldest and largest V6 Mustang forum on the internet. If you have any questions about your V6 Mustang or just want to connect with other V6 Mustang owners around the world, you have found the best place on the internet to do that.

Registering is free and easy! Hope to see you on the forums soon!

Captain Max's Place

  • 10/18/19 NOW: Been A Couple Of Years Rebuilding My 2000 Mustang Changed: Now 4.2L V6, 50/50 Comp Cam, Scorpion Roller Rockers, Comp Cams 302 lifters Manley .120 Wall Push Rods, Shaved Main Caps For Morana Stud Girdle, F150 4Wheel Drive Oilpan To Fit Over Main Caps, (3.8L Not Workable) Will List As I Get Time Everything Else. Or See Pictures Below!
    Then: Improving Handling and Run Ability In General,3.8L 5 Speed
    I've Upgraded The Ignition, Accel Coil Pack, Bosch +4 Plat- Iridium Plugs, Wires, Cold Air Induction, Converted To Duel Exhaust, Shorty Headers, New Injectors (Bosch 4 Pintel 19# Upgrade). 9.8124R Sway Bar End Link Kit Red Performance Polyurethane, Have KYB Shocks All Around, Front Coil Overs, Engine Strut Brace, Full Tubular K Member UPR Front Suspension , Upper and Lower Rear Control Arms With Torque Boxes And Rear Sway Bar Installed, New Lowered Springs Rear, 1.5 Spacers Front 2" Spacers Rear,17"X9 AM Classic 5 Spoke Wheels with General G-MAX AS-03 Tire 245/45ZR17SL 95W BW All around. But You Could Say I've Not Made Any Other Mods. Truth Is I Do Plan Others! That's Why I'm Here To Pick Brains And Get Other Ideas. Powers No Good If You Can't Put It On The Ground!!!. 2000 Mustang Coupe Base

    New 9/1/16: 19lbs 4 pintel injectors from 5.0 , Ported Upper And Lower Intakes, 70MM Throttle Body , New K Member ,Coil Overs, Scorpion 1.73 Roller Rockers, Manley Push Rods .020 Over Stock, Al Driveshaft, Modified Exhaust With Balance Tube, Duels, 373's LSD , 2800 Lb. Clutch, P&P, Heads Out Of Machine Shop (Ported) I'm Getting There!
    6/12/17 Have 12 Pintel 24# Injectors To Install With Phenolic Spacer Between Upper And Lower Manifold, Moog Front Hubs. I'm LQQKING Into Upgraded Fuel System.
    6/28/17 Still Working On Front End, Installed Offset Bushings To Steering Rack On UPR K Member, New Inner Tie Rods, Boots And Bump Steer Kit New Brake Dust Shields And Hub Spacers.
    Getting Old Taking More Time Than It Used Too!!!
    7/7/17 Installed 30MM Front Sway Bar With Prothane Bushings, Replacing 25MM Sway Bar. Now 30MM Front And 23MM Rear.
Nergion, Spdricer and Banyan Long like this.

User Comments

To post comments, simply sign up and become a member!
  1. Captain Max Silver
    New Tires And Wheels, 5 Spoke Bullitt AM 17"X 9" And A Set Of
    General G-MAX AS-03 Tire 245/45ZR17SL 95W BW Nice Handling Set Up.
      CrzyMunk and SixPackSurprise like this.
  2. Captain Max Silver
    Been Working On Hood Of My 2000 Mustang Have Incorporated Hood Vents
    From 2015-17 Mustang Into It. One Of A Kind!! (I Think) Check My Build Page
    For Updates.
      Spdricer likes this.
  3. Edward S
    I check this garage every time I log on, im hooked on following your build. keep it up
    1. Captain Max Silver
      Thanks!
      Captain Max Silver, Nov 5, 2019
  4. Captain Max Silver
    Pete fender How'd You Guess!! LOL 24# Jeep 12 Pintel.
    Bosch Fuel Injector Upgrade 01-07 Jeep WJ WK XK 4.7L V8 EV6 12-Hole
    Just Have To Retune For 4.2L 50/50 Compcams. And Everything Else I've Put Into This.
    1. View previous replies...
    2. Captain Max Silver
      In My Case I'm Running Rich At Moment, Need To Retune For These Injectors. But Expect Some Gain. Are You Running Stock Camshaft?
      Captain Max Silver, Oct 2, 2019
    3. Pete fender
      The stock cam, same one the 4.2 F150 used.
      It does not make much power until about 1800 rpm.
      Another, a 99 Mustang I modified and sold I put a F150 4.2 manifold on it.
      I had to go to a higher stall speed converter, but it was worth it.
      Pete fender, Oct 2, 2019
      Captain Max Silver likes this.
  5. Captain Max Silver
    Getting Closer, Cooling System In Just Need to Wire Secondary Fans To Dash And Install Starter Setup. Over Flow Tank Should Be In By Monday (I Hope) Working On Hood For Vent Mod's And See How It LQQKS. Almost On Road Again!! Vents Are From 2015 Mustang, LQQK Like Good Fit.
  6. Captain Max Silver
    I Got The Hoses On Today, Like The Extra Wide Clamps We Have Today, LQQK Good And Hold Great Too! With The 4.6L Mustang Radiator In Place Needed To Find A Way To Fill Her Up With Coolant. So I Got Out My Trusty PVC Pipe Cutting Pliers. Ever See Them Massive Ratcheting Jaw And It Cut Silicone Hose With Ease. Nice Smooth Straight Cuts. Inserted Filler Coupling With Filler And There You Have It. One Thing I Noticed Is My Overflow Isn't Going To Fit. Any Ideas (Out There) As To Which To Use? Check Out My Projects In Personal Projects and Builds.
  7. Captain Max Silver
    If You Want To See Some Of My Build Go To Forums, Personal Projects and Builds And Check It Out!
  8. Captain Max Silver
    Been Down For About A Year Workin On My Baby! New 4.2l V6 Ported Polished Heads, P/P Upper And Lower Intake With Phenolic Spacer 24Lbs. 12 Pintel Injectors, 50/50 CompCams Bumpy Stick, Scorpion Roller Rockers, Manley Push Rods .120",CompCams Lifters, Compcam Beehive Valve Springs, New Valve Locks, Arp Head Studs, Arp Crankshaft Studs, Morana Stud Girdle, 6 Qt. Oil Pan, Manley Timing Set. Lot's Of Other Parts Will List Later. Been Busy!
    1. Spdricer
      Cool man make a thread in the project section
      Spdricer, May 23, 2019
      Captain Max Silver likes this.
  9. Captain Max Silver
    Dropped New 4.2L Engine In. Got More To Do But She's In And Locked Down. Just Need To Wire Up Install Intake Set Up And See If She Fires Up. Then The Rest Before All Ready For Road. Getting There!!
  10. Captain Max Silver
    It's Been A While Since I Posted Any Updates But Just About Ready To Drop My New 4.2L Engine In My 2000 Mustang. Had A Few Road Blocks Along The Way, Frame Problems, Repairs To Shock Towers, Finding The Right (I Hope) Combination Of Parts For This New 4.2L Block With My 3.8L Parts. Will Find Out Soon.