Search results

  1. billegoat

    4.2 Stroker build projected HP and Questions

    To answer your question about the throttle body on a Windstar intake, I've got one on my 3.9 and I put a bbk 70mm 04 gt throttle body on it, had to use a throttle spacer then I blended the front out to match the 70mm. Without the spacer the throttle blade will hit the intake. Also I used jb weld...
  2. billegoat

    Metal shavings on lifter body when removed

    There are a couple write ups here on replacing the oil pump, if it was mine I would take off pump and see what it looks like, look for scratches and scars on gears and housing...all though, with it having metal in the lifters I'm sure it's got the bearings damaged too.
  3. billegoat

    Metal shavings on lifter body when removed

    That doesn't look good, need to put a manual gauge in where the oil sending switch screws in, and see what the oil pressure is with cold motor and warm it up and see how far it falls. I'm gonna say you prolly have a oil pump issue....
  4. billegoat

    Metal shavings on lifter body when removed

    The gauges on our cars are just dummy gauges, they work like a light, either show little over half or nothing.... I've cut open oil filters on diesel engines to check for oil pump damage, take a cutoff tool and cut through the metal case about 1/4" below the heavy metal top and pull it apart...
  5. billegoat

    Metal shavings on lifter body when removed

    Any idea how much oil pressure it had before you took it apart? It could be oil pump damage if it was run low on oil....
  6. billegoat

    2000 mustang t5 swap

    My swap was using a 98 trans, but my car already had a manual, and it had the gears with a mag pickup, I could be wrong but I thought 98 or 99 was last year for the gear set up....
  7. billegoat

    2000 mustang t5 swap

    Looks like the company has went out of business, the only option I know of is either find a used one, it's called a Dallas mustang speedcal, or buy a tuner and get someone like BAMA to write a tune to correct it.....
  8. billegoat

    2000 mustang t5 swap

    Either a tune or a signal converter....I have a 98 t5 in my 04 and I use a Dallas mustang speedometer converter.
  9. billegoat

    2000 mustang t5 swap

    Has to be either in the ecm being on an auto before, or it's a 01-04 t5 I don't know for sure when the speedo sensor change from gear driven to just a magnetic pickup but the signal frequency is way different....
  10. billegoat

    Sup everyone

    Welcome to the forum!
  11. billegoat

    My Windstar swap

    Finally got around to putting it all together. Just thought I'd share few pictures. 2004 base 3.9l, bama x4, shorty headers full 2 1/2" stainless exhaust with x pipe and flow master delta 40, t-5, 8.8 Trac loc with 3.73, bama sct x4, the swap gave it alot more low end. Haven't taken it out of...
  12. billegoat

    V6 throttle issue

    Search this forum, I had to make a baffle for my iac.....I have a kn fipk cold air and have found by making a cover over the top it helped my high idle when coasting above 20 mph....
  13. billegoat

    ABS and tire slipping warning light

    Get someone to pull the codes, bet it's a wheel speed sensor...
  14. billegoat

    Language

    It's some sort of spam bot or something.....several have sent messages to moderators with no response...
  15. billegoat

    Ads

    I know I have fixed many issues searching this board, would be a shame to see it go...
  16. billegoat

    Ads

    I used to enjoy looking threw and reading posts on this site.....looks like some sort of bot has taken it over....
  17. billegoat

    Rich in one bank, lean in the other, equal on load

    A bent push rod, any kind of damage to the rocker arm will cause compressions like that....also remember you have Hyd roller lifters that can have an issue to, I've seen on Ls motors have valve to piston strikes and damage lifters and nothing else.
  18. billegoat

    Need help with fuel pressure test

    My 04 3.9 doesn't have it either ...
  19. billegoat

    2000 v6 Completed Windstar Finally!! Stock Hood!

    So did you make the angled thottle spacer or buy it?
  20. billegoat

    Throttle body

    I'm a farm equipment mechanic.....they won't be a problem. I just deal mostly with diesels, these mods are little different from what I've done....
Top