Latest activity

  • J
    James123 replied to the thread Sup everyone.
    Howdy! What mods have you done so far?
  • Z-01Sixer
    Where are you located? Still have the t5?
  • T
    TRUEBLUE1968 replied to the thread 3.7 Cyclone V6 Swap.
    I will be looking for a MT82, the Quicktime bellhousing to adapt a Tremec plus the Tremec is close to 3200,00
  • P
    PerroCaliente replied to the thread 3.7 Cyclone V6 Swap.
    If you're able to use a T56, T5 (would have to be beefed up), TKO, OR TKX. Basically anything other than an MT82 you'll have less...
  • P
    PerroCaliente replied to the thread 3.7 Cyclone V6 Swap.
    You could use the factory drive by wire pedal. That's what I did. Works fine. There's a bracket that you can get to bolt it in as well...
  • T
    TRUEBLUE1968 replied to the thread 3.7 Cyclone V6 Swap.
    I am, I have a 98 and just need a transmission, as well as a drive by wire solution the pump mounts below the A/C compressor, there is...
    • received_797236870858576.jpeg
    • received_345280510384200.jpeg
    • received_191838042956797.jpeg
    • kermit 3.8.jpg
    • kermit k member.jpg
  • BRN2RUN
    I have an Autometer 7002 gauge cluster for sale. In very good condition. Fits a 1999 to 2003 V6 Mustang (not sure why it doesn't fit a...
    • IMG_20220524_182142144.jpg
  • P
    PerroCaliente replied to the thread 3.7 Cyclone V6 Swap.
    Are you trying to swap it as well? You don't need a new body harness if you go my route. I meant I left my 2000 mustang body harness...
  • T
    TRUEBLUE1968 replied to the thread 3.7 Cyclone V6 Swap.
    I actually have everything except the Body harness, MT82 and transmission crossmember. So Thank you for the information. I have a 17'...
  • Flex
    Flex replied to the thread 2004 3.8 m112 swap.
    Wondering if you ever did this?
  • Echonan
    Echonan replied to the thread 3.7 Cyclone V6 Swap.
    I bought a coyote swap harness from Power by the Hour and connected that up to a 2014 Mustang V6 PCM with the PATS deleted. I had to...
  • T
    TRUEBLUE1968 replied to the thread 3.7 Cyclone V6 Swap.
    How did you incorporate the 3.7 harness to the SN? And the transmission mount? hydro clutch?
  • P
    PerroCaliente replied to the thread 3.7 Cyclone V6 Swap.
    Now if you've made it this far you're probably wondering, what did he use to mount that engine? Fret not, I too wondered that for a LONG...
    • IMG_20180924_155216.jpg
    • IMG_20180924_155205.jpg
    • IMG_20180924_155315.jpg
    • IMG_20170211_203622.jpg
    • IMG_20180711_170027.jpg
    • IMG_20180924_155253.jpg
    • IMG_20180711_170020.jpg
    • IMG_20170211_203635.jpg
    • IMG_20180814_194903.jpg
    • IMG_20180924_155211.jpg
  • P
    PerroCaliente replied to the thread 3.7 Cyclone V6 Swap.
    I'll break this down into sections as best I can. I'll start with the 3.7 engine. Approximately 30k miles, 2014, 3.7 out of a Mustang. I...
    • IMG_20180816_102947.jpg
    • IMG_20180816_102944.jpg
    • IMG_20180816_102941.jpg
    • IMG_20180816_103013.jpg
    • IMG_20180816_103001.jpg
    • IMG_20180816_102958.jpg
    • IMG_20180816_102953.jpg
    • IMG_20180817_112512_679.jpg
    • IMG_20180816_103033.jpg
    • IMG_20180814_194929.jpg
    • IMG_20170801_192030.jpg
    • IMG_20170801_192024.jpg
    • IMG_20170801_192059.jpg
    • IMG_20170801_192049.jpg
  • P
    PerroCaliente replied to the thread 3.7 Cyclone V6 Swap.
    Here's the car in question. A 2000 Tropic Green Mustang. Originally a 3.8 5 speed V6. It briefly had a semi built 4.3 V6. I swapped to...
    • IMG_20190511_165603.jpg
    • IMG_20190511_165618.jpg
    • IMG_20190511_165558.jpg
Top